Construction:
This dress was a real job! I did tons of research while making this gown. I studied every picture I could get my hands on, followed two forum threads on the dress, listened to tons of other girl's suggestions, and experimented galore. I have never felt so proud of any costume I completed!
I made a mock up out of muslin first. The main dress went together very well, but required some minor fitting, as the bust was full in a weird place and stuck out dreadfully. I also altered the neckline, making a facing to create a nice edge and a clean cut V in the front. I tested out numerous decorative stitch combos on my Platinum 770 until I finally came up with one I liked.
The sleeve was a whole different matter. My first one was way too tight (and I have really thin arms!) and extremely restricting. I made the sleeve width the biggest size and tried another sleeve. It was still too tight across the shoulders and I could hardly lift my arms. Then I drew the top line of the sleeve higher on the sides. This gave me more fabric under the arms and solved my problem, making the sleeves very comfortable.
I made the slashes the way Philo of Narniaweb and Sensibility suggested:
If I were to do them, I would probably make an individual "facing" for each slit. I haven't searched the internet for good instructions on this, but here's my own try: Cut a facing for each slit, a rectangle a couple inches bigger than the finished elipse. Mark the elipse on the wrong side of facing fabric, then with right sides together, sew the sleeve and facing together along the markings. You'll probably want to reinforce the top and bottom by going over the stitching. Cut out the center elipse, trimming close at the corners. Then turn the facing through the whole to the inside of the sleeve. Secure as necessary (topstitch if desired).
I followed her instructions nearly exactly and my slashes came out better than I originally dreamed they would. Thanks so much, Philo!!!
The last thing I did on the sleeves was draw the bottom edge so that it curved down from the wrist over the top of my hand. I also added a little width at the bottom sides, to create the slight flare that is obvious in so many pictures.
So, on December 9th, to celebrate the opening of the movie, I cut out my entire dress. As you can guess, I didn't finish it in time to see the movie in, but that's OK- I'm still happy! :) I'll just say here, be careful when you cut the dress out! It's really confusing and easy to mess up the pieces and not fit them all on your fabric - unless you follow the cutting guide on page one of your pattern instructions.
The dress went together well. I attached the body of the dress and the lining together at the armholes and hem and when I sewed the sleeves on, I left the lining free and slipstiched that in by hand. Thus, the whole inside of the dress is lined and has a very clean finish.
I used my Platinum 770 to do the "embroidery" and it came out very nice. I stitched the eyelets at the front neckline by hand and cut two short pieces of the suede lacing, put them through the holes and stitched those in by hand. To get the underdress to show around the neckline, I did only a 1/4" seam allowance around the underdress neckline, instead of the 5/8" on the dress neckline; therefore, I have about 3/8" of the underdress showing and I really like how it looks.
The back of the underdress I fastened with loops and buttons. I sewed the buttons on the inside of the dress, so you only see the edges of the dress line up on the outside. Then I fitted the overdress to my dressform (this was before the two dress bodies were attached at the armholes) and made the top edges 1 1/2" away from each other, gradually tapering down to a point. Then I folded the edges under and made a nice little seam along the edge (Oh! BTW, I made the bottom of the back opening two inches higher than on the pattern, as I wanted it to come down to where the belt would run so that you wouldn't see the bottom of the opening.
Next, I made a placket of the dress fabric to fill in the back opening and hand-stitched that to one side of the opening. I put snaps on the other side of the opening and placket to anchor it securely. Then I got some big eyes (you know, hook and eyes. I think mine were size 3) and sewed 10 (I think) on either side of the opening. When I put the dress on, one of my younger sisters would first button up the underdress, and then snap the placket together across the back. Lastly, she would lace the dress all the way down. As I didn't like the way it looked tied down at the end of the opening, I put another eye at the bottom of the opening on the inside of the dress. My sister would just pull the laces securely through that eye and tuck them down inside the dress. I might add that it does take a few minutes to get the dress on completely.
Well, I think that's pretty much all I can think of about making the dress. I am very happy with the way everything turned out! I was so afraid that there would be something "not-quite-right" with the dress, but it's absolutely perfect! I wasn't able to finished the belt as my machine is having some problems with the faux leather (It must be my fault - I can't believe that a $1500 machine doesn't know what it's doing!). It was a lot of work, but SO worth it!!! |