This is the hacked configure script I used to compile pcmcia modules for the
Toshiba T2150CDT. My hacks are emphasized. Basically, they force both
Cardbus and PNP support to be disabled, despite what make-kpkg does. And no,
running make-kpkg configure won't let you get around this cleanly. I plan to
complain Real Soon Now. :)
#!/bin/bash
#
# Configure 1.232 2003/08/13 06:26:23
#
# The contents of this file are subject to the Mozilla Public License
# Version 1.1 (the "License"); you may not use this file except in
# compliance with the License. You may obtain a copy of the License at
# http://www.mozilla.org/MPL/
#
# Software distributed under the License is distributed on an "AS IS"
# basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
# the License for the specific language governing rights and
# limitations under the License.
#
# The initial developer of the original code is David A. Hinds
# <dhinds@pcmcia.sourceforge.org>. Portions created by David A. Hinds
# are Copyright (C) 1999 David A. Hinds. All Rights Reserved.
#
# Alternatively, the contents of this file may be used under the terms
# of the GNU General Public License version 2 (the "GPL"), in which case
# the provisions of the GPL are applicable instead of the above. If you
# wish to allow the use of your version of this file only under the
# terms of the GPL and not to allow others to use your version of this
# file under the MPL, indicate your decision by deleting the provisions
# above and replace them with the notice and other provisions required
# by the GPL. If you do not delete the provisions above, a recipient
# may use your version of this file under either the MPL or the GPL.
#
#=======================================================================
fail ()
{
echo ""
echo "Configuration failed."
echo ""
exit 1
}
qgrep ()
{
grep $* >/dev/null 2>&1
}
# Minimal requirements for sanity
if [ ! -L include/linux/config.h ] ; then
echo "Ack! The PCMCIA distribution is incomplete/damaged!"
echo " Unpack again -- and try using a Linux filesystem this time."
fail
fi
if ! make -v >/dev/null ; then
echo "Ack! This system does not have a 'make' command!"
echo " Install a normal set of Linux development tools and try again."
fail
fi
if [ -r config.out ] ; then
. ./config.out 2>/dev/null
else
if [ ! -r config.in ] ; then
echo "config.in does not exist!"
fail
fi
. ./config.in
fi
#=======================================================================
PROMPT=y
FORCE=$FORCE_CONFIG_PCMCIA
arg () {
VALUE="`echo X"$2" | sed -e 's/^X--[a-zA-Z_]*=//'`"
eval $1=\"$VALUE\"
}
usage () {
echo "usage: $0 [-n|--noprompt] [--kernel=src-dir] [--target=dir]"
echo " [--moddir=dir] [--arch={i386|alpha|arm|ppc] [--ucc=path]"
echo " [--kcc=path] [--ld=path] [--uflags=flags] [--kflags=flags]"
echo " [--debug=flags] [--{no}trust] [--{no}cardbus] [--{no}pnp]"
echo " [--{no}apm] [--force] [--current] [--srctree] [--sysv]"
echo " [--bsd] [--rcdir=dir] [--extraver=ver]"
echo ""
echo " -n, --noprompt non-interactive mode: no prompting"
echo " --kernel=DIR use kernel source tree at DIR"
echo " --target=DIR install all files using DIR as root"
echo " --moddir=DIR install modules under DIR"
echo " --arch=ARCH select target architecture for build"
echo " --ucc=PATH specify C compiler for user code"
echo " --kcc=PATH specify C compiler for kernel code"
echo " --ld=PATH use another linker"
echo " --uflags=FLAGS set compiler flags for user-mode tools"
echo " --kflags=FLAGS set compiler flags for kernel modules"
echo " --debug=FLAGS set compiler flags for debugging"
echo " --{no}trust disable or enable trusted user tools"
echo " --{no}cardbus disable or enable CardBus card support"
echo " --{no}pnp disable or enable PnP BIOS support"
echo " --{no}apm disable or enable power management support"
echo " --force ignore presence of 2.4 kernel drivers"
echo " --current read configuration of current kernel"
echo " --srctree read kernel configuration from source tree"
echo " --sysv target has SysV init script layout"
echo " --bsd target uses BSD init scripts"
echo " --rcdir=DIR SysV init scripts are under DIR"
echo " --extraver=VER overrides EXTRAVERSION in kernel Makefile"
exit 1
}
while [ $# -gt 0 ] ; do
case "$1" in
-n|--noprompt) PROMPT=n ;;
--kernel=*) arg LINUX $1 ;;
--target=*) arg PREFIX $1 ;;
--moddir=*) arg MODDIR $1 ;;
--cc=*) arg UCC "$1" ;;
--ucc=*) arg UCC "$1" ;;
--kcc=*) arg KCC "$1" ;;
--ld=*) arg LD "$1" ;;
--debug=*) arg PCDEBUG "$1" ;;
--kflags=*) arg KFLAGS "$1" ;;
--uflags=*) arg UFLAGS "$1" ;;
--arch=*) arg ARCH "$1" ;;
--trust) UNSAFE_TOOLS=y ;;
--notrust) UNSAFE_TOOLS=n ;;
--cardbus) CONFIG_CARDBUS=n ;;
--nocardbus) CONFIG_CARDBUS=n ;;
--pnp) CONFIG_PNP_BIOS=n ;;
--nopnp) CONFIG_PNP_BIOS=n ;;
--apm) USE_PM=y ;;
--noapm) USE_PM=n ;;
--force) FORCE=y ;;
--current) CONF_SRC=1 ;;
--srctree) CONF_SRC=2 ;;
--sysv) SYSV_INIT=y ;;
--bsd) SYSV_INIT=n ;;
--rcdir=*) arg RC_DIR "$1" ;;
--extraver=*) arg EXTRAVER "$1" ;;
*) usage ;;
esac
shift
done
#=======================================================================
if [ ! "$UCC" ] ; then UCC=cc ; fi
if [ ! "$KCC" ] ; then
if which kgcc >/dev/null 2>&1 ; then KCC=kgcc ; else KCC="$UCC" ; fi
fi
if ! $UCC -v >/dev/null 2>&1 ; then
echo "Ack! Your system does not have '$UCC' installed!"
echo " Install a normal set of Linux development tools and try again."
fail
fi
if ! $KCC -v >/dev/null 2>&1 ; then
echo "Ack! Your system does not have '$KCC' installed!"
echo " Install a normal set of Linux development tools and try again."
fail
fi
#=======================================================================
CONFIG=config.new
CONFIG_H=include/pcmcia/autoconf.h
CONFIG_MK=config.mk
MODVER=include/linux/modversions.h
rm -f .prereq.ok $CONFIG $CONFIG_H $CONFIG_MK $MODVER
cat << 'EOF' > $CONFIG
#
# Automatically generated by 'make config' -- don't edit!
#
EOF
cat << 'EOF' > $CONFIG_H
/*
Automatically generated by 'make config' -- don't edit!
*/
EOF
write_bool() {
value=`eval echo '$'$1`
if [ "$value" = "y" ] ; then
echo "$1=y" >> $CONFIG
echo "$1=y" >> $CONFIG_MK
echo "#define $1 1" >> $CONFIG_H
else
echo "# $1 is not defined" >> $CONFIG
echo "# $1 is not defined" >> $CONFIG_MK
echo "#undef $1" >> $CONFIG_H
fi
}
write_int () {
value=`eval echo '$'$1`
echo "$1"=$value >> $CONFIG
echo "$1=$value" >> $CONFIG_MK
echo "#define $1 $value" >> $CONFIG_H
}
write_str () {
value=`eval echo '$'$1`
echo "$1"=\"$value\" >> $CONFIG
echo "$1=$value" >> $CONFIG_MK
echo "#define $1 \"$value\"" >> $CONFIG_H
}
prompt () {
eval $3=\"$2\"
if [ "$PROMPT" = "y" ] ; then
/bin/echo -e "$1 [$2]: \c"
read tmp
if [ ! -t 1 ] ; then echo $tmp ; fi
if [ -n "$tmp" ] ; then eval $3=\"$tmp\" ; fi
else
/bin/echo "$1 [$2]"
fi
}
ask_bool () {
default=`eval echo '$'$2`
if [ ! "$default" ] ; then default=n ; fi
answer=""
while [ "$answer" != "n" -a "$answer" != "y" ] ; do
prompt "$1 (y/n)" "$default" answer
done
eval "$2=$answer"
write_bool $2
}
ask_str () {
default=`eval echo '$'$2`
prompt "$1" "`echo $default`" answer
eval $2=\"$answer\"
write_str $2
}
#=======================================================================
echo ""
echo " -------- Linux PCMCIA Configuration Script --------"
echo ""
echo "The default responses for each question are correct for most users."
echo "Consult the PCMCIA-HOWTO for additional info about each option."
echo ""
if [ ! "$LINUX" ] ; then
if [ -d /lib/modules/`uname -r`/build ] ; then
LINUX=/lib/modules/`uname -r`/build
else
LINUX=/usr/src/linux
fi
fi
ask_str "Linux kernel source directory" LINUX
match () { case "$1" in $2) return 0; ;; *) return 1;; esac ; }
if ! match "$LINUX" "/*" ; then
echo "$LINUX is not an absolute path!"
fail
fi
if [ ! -f $LINUX/kernel/Makefile ] ; then
echo "Linux source tree '$LINUX' is incomplete or missing!"
if [ -d $LINUX/include/linux ] ; then
echo " The kernel header files are present, but not " \
"the full source code."
fi
echo " See the HOWTO for a list of FTP sites for current" \
"kernel sources."
fail
fi
# What kernel are we compiling for?
version () {
expr $1 \* 65536 + $2 \* 256 + $3
}
echo ""
for TAG in VERSION PATCHLEVEL SUBLEVEL EXTRAVERSION ; do
eval `sed -ne "/^$TAG/s/[ ]//gp" $LINUX/Makefile`
done
if [ "$EXTRAVER" != "" ] ; then
EXTRAVERSION=$EXTRAVER
write_str EXTRAVER
fi
if [ "$KVERS" ]; then
SRC_RELEASE=$KVERS
else
SRC_RELEASE=$VERSION.$PATCHLEVEL.$SUBLEVEL$EXTRAVERSION
fi
SRC_BASE=$VERSION.$PATCHLEVEL.$SUBLEVEL
VERSION_CODE=`version $VERSION $PATCHLEVEL $SUBLEVEL`
echo "The kernel source tree is version $SRC_RELEASE."
if [ $VERSION_CODE -lt `version 2 0 0` ] ; then
echo "This package requires at least a 2.0 series kernel."
fail
elif [ $VERSION_CODE -ge `version 2 1 0` -a \
$VERSION_CODE -lt `version 2 2 0` ] ; then
echo "2.1 kernels are not supported. Upgrade to 2.2."
fail
elif [ $VERSION_CODE -ge `version 2 3 0` -a \
$VERSION_CODE -lt `version 2 4 0` ] ; then
echo "2.3 kernels are not supported. Upgrade to 2.4."
fail
fi
# Debian hack: Fall back on gcc272 for 2.2 kernels
if [ "$KCC" = "$UCC" ] && \
[ $VERSION_CODE -ge `version 2 2 0` -a \
$VERSION_CODE -lt `version 2 3 0` ] && \
which gcc272 >/dev/null 2>&1 ; then KCC=gcc272
fi
# END Debian hack
HOST_ARCH=`uname -m | sed -e 's/i.86/i386/'`
if [ ! "$ARCH" ] ; then ARCH=$HOST_ARCH ; fi
CUR_RELEASE=`uname -r`
CUR_VERSION=`uname -v`
CUR_BASE=`uname -r | sed -e "s/^\([0-9]\.[0-9]\.[0-9]*\).*/\1/"`
MATCH=0 # default: different releases and/or architectures
if [ $ARCH = $HOST_ARCH ] ; then
if [ $CUR_RELEASE = $SRC_RELEASE ] ; then
MATCH=1 # same release, perfect match
elif [ $CUR_BASE = $SRC_BASE ] ; then
MATCH=1 # well, maybe same source tree
echo " WARNING: the current kernel is sublevel $CUR_RELEASE."
else
echo " WARNING: the current kernel is version $CUR_RELEASE."
fi
fi
# Check for consistent kernel build dates
CUR_D=`uname -v | sed -e 's/^#[0-9]* //;s/SMP //'`
CUR_D=`echo $CUR_D | sed -e 's/\(:[0-9][0-9]\) .* \([12][90]\)/\1 \2/'`
echo "The current kernel build date is $CUR_D."
SRC_VERSION="unknown";
if [ -f $LINUX/include/linux/compile.h ] ; then
SRC_VERSION=`grep UTS_VERSION $LINUX/include/linux/compile.h |
sed -e 's/.*"\(.*\)"/\1/'`
SRC_D=`echo $SRC_VERSION | sed -e 's/^#[0-9]* //;s/SMP //'`
SRC_D=`echo $SRC_D | sed -e 's/\(:[0-9][0-9]\) .* \([12][90]\)/\1 \2/'`
if [ $MATCH = 1 -a "$SRC_D" != "$CUR_D" ] ; then
echo " WARNING: the source tree has a build date of $SRC_D."
if [ `date -d "$SRC_D" +%s` -gt `date -d "$CUR_D" +%s` ] ; then
echo " Did you forget to install your new kernel?"
fi
elif [ $MATCH = 1 ] ; then
MATCH=2 # same release & date
fi
fi
echo ""
for x in PREFIX KCC UCC LD KFLAGS UFLAGS PCDEBUG ; do
write_str $x
done
write_bool USE_PM
ask_bool "Build 'trusting' versions of card utilities" UNSAFE_TOOLS
ask_bool "Include 32-bit (CardBus) card support" CONFIG_CARDBUS
CONFIG_CARDBUS=n
# if [ $ARCH = "i386" -a $VERSION_CODE -gt `version 2 2 0` ] ; then
# CONFIG_PNP_BIOS=y
# ask_bool "Include PnP BIOS resource checking" CONFIG_PNP_BIOS
# else
CONFIG_PNP_BIOS=n
write_bool CONFIG_PNP_BIOS
# fi
if [ $MATCH = 0 ] ; then
CONF_SRC=2 # Use source tree when required to do so
elif [ $MATCH = 2 ] ; then
CONF_SRC=3 # Use source tree when safe to do so
elif [ $MATCH = 1 -a ! -r $LINUX/.config ] ; then
CONF_SRC=1 # Use running kernel if tree is not configured
elif [ "$PROMPT" = "y" ] ; then
echo ""
echo "The PCMCIA drivers need to be compiled to match the kernel they"
echo "will be used with, or some or all of the modules may fail to load."
echo "If you are not sure what to do, please consult the PCMCIA-HOWTO."
echo ""
echo "How would you like to set kernel-specific options?"
echo " 1 - Read from the currently running kernel"
echo " 2 - Read from the Linux source tree"
ans=""
while [ "$ans" != 1 -a "$ans" != 2 ] ; do
prompt "Enter option (1-2)" "$CONF_SRC" ans
done
CONF_SRC=$ans
echo ""
fi
echo "CONF_SRC=$CONF_SRC" >> $CONFIG
if [ $CONF_SRC = 1 ] ; then
UTS_VERSION=$CUR_VERSION ; UTS_RELEASE=$CUR_RELEASE
else
UTS_VERSION=$SRC_VERSION ; UTS_RELEASE=$SRC_RELEASE
fi
write_str UTS_RELEASE
write_str UTS_VERSION
echo "LINUX_VERSION_CODE=$VERSION_CODE" >> $CONFIG
echo "LINUX_VERSION_CODE=$VERSION_CODE" >> $CONFIG_MK
echo "#define LINUX_VERSION_CODE $VERSION_CODE" >> $CONFIG_H
echo "#define KERNEL_VERSION(a,b,c) (((a) << 16) + ((b) << 8) + (c))" \
>> $CONFIG_H
echo "" >> $CONFIG
echo "" >> $CONFIG_MK
echo "" >> $CONFIG_H
if [ ! "$MODDIR" ] ; then
if [ -d /lib/modules/preferred ] ; then
MODDIR=/lib/modules/preferred
else
MODDIR=/lib/modules/$UTS_RELEASE
fi
else
MODDIR=`echo $MODDIR | \
sed -e "s/[0-9]\.[0-9]\.[0-9]*.*/$UTS_RELEASE/"`
fi
ask_str "Module install directory" MODDIR
if ! match "$MODDIR" "/lib/modules/*" ; then
if match "$MODDIR" "[yY]" ; then
echo "Selected directory '$MODDIR' is bogus!"
fail
fi
echo "WARNING: '$MODDIR' is an unusual target. Be careful!"
fi
echo ""
#=======================================================================
symcheck () {
eval "CONFIG_$1=n"
if $KSYMS | qgrep "$2" ; then eval "CONFIG_$1=y" ; fi
if [ "$3" ] ; then
/sbin/insmod $3 > /dev/null 2>&1
if $KSYMS | qgrep "$2" ; then eval "CONFIG_$1=y" ; fi
fi
}
configcheck () {
eval "CONFIG_$1=n"
if qgrep "^CONFIG_$1=y" $AUTOCONF ; then
eval "CONFIG_$1=y"
elif qgrep "^CONFIG_$1=m" $AUTOCONF ; then
eval "CONFIG_$1=y"
fi
}
configcheckint () {
eval "CONFIG_$1=$2"
if qgrep "^CONFIG_$1=[0-9][0-9]*$" $AUTOCONF ; then
eval `qgrep "^CONFIG_$1=[0-9][0-9]*$" $AUTOCONF`
fi
}
printflag() {
value=`eval echo '$'$2`
/bin/echo -e " $1 is \c"
if [ "$value" = "y" ] ; then
echo "enabled."
else
echo "disabled."
fi
write_bool $2
}
x86_config_tweak () {
CONFIG_X86_L1_CACHE_BYTES=32
write_int CONFIG_X86_L1_CACHE_BYTES
CONFIG_X86_L1_CACHE_SHIFT=5
write_int CONFIG_X86_L1_CACHE_SHIFT
if [ $VERSION_CODE -ge `version 2 2 0` ] ; then
if [ $CONFIG_SMP = "y" ] ; then
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
write_bool CONFIG_X86_LOCAL_APIC
write_bool CONFIG_X86_IO_APIC
fi
if [ $CONFIG_PCI = "y" ] ; then
CONFIG_PCI_QUIRKS=y
write_bool CONFIG_PCI_QUIRKS
fi
fi
if [ $VERSION_CODE -ge `version 2 4 0` ] ; then
write_bool CONFIG_EISA
CONFIG_X86_CMPXCHG=y
if [ "$CONFIG_RWSEM_GENERIC_SPINLOCK" = "y" ] ; then
CONFIG_X86_CMPXCHG=n
fi
write_bool CONFIG_X86_CMPXCHG
fi
if [ "$BIGMEM" ] ; then
if [ "$CONFIG_3GB" = "y" ] ; then MEMMAX=3GB
elif [ "$CONFIG_2GB" = "y" ] ; then MEMMAX=2GB
else MEMMAX=1GB ; fi
echo " Maximum physical memory: $MEMMAX"
echo "MEMMAX=$MEMMAX" >> $CONFIG
write_bool CONFIG_1GB
write_bool CONFIG_2GB
write_bool CONFIG_3GB
fi
printflag "PAE support" CONFIG_X86_PAE
}
alpha_config_tweak () {
if [ $VERSION_CODE -lt `version 2 2 0` ] ; then
CONFIG_ALPHA_LCA=y
write_bool CONFIG_ALPHA_LCA
else
CONFIG_ALPHA_GENERIC=y
write_bool CONFIG_ALPHA_GENERIC
fi
}
ppc_config_tweak () {
printflag "MPC8xx architecture" CONFIG_8xx
printflag "IBM 4xx processor" CONFIG_4xx
printflag "Embedded Planet LITE platform" CONFIG_RPXLITE
printflag "Embedded Planet CLASSIC platfom" CONFIG_RPXCLASSIC
printflag "MPC823 processor" CONFIG_MPC823
printflag "MPC850 processor" CONFIG_MPC850
printflag "MPC860 processor" CONFIG_MPC860
printflag "MPC860T processor" CONFIG_MPC860T
if [ $VERSION_CODE -gt `version 2 4 0` ] ; then
CONFIG_ALL_PPC=y
write_bool CONFIG_ALL_PPC
fi
}
arm_config_tweak () {
printflag "Brutus architecture" CONFIG_ARCH_BRUTUS
printflag "Itsy target platform" CONFIG_ITSY
}
printconfig () {
echo "Kernel configuration options:"
if [ $VERSION_CODE -ge `version 2 3 18` ] ; then
printflag "Kernel-tree PCMCIA support" CONFIG_PCMCIA
fi
printflag "Symmetric multiprocessing support" CONFIG_SMP
if [ "$CONFIG_SMP" = "y" ] ; then
echo "#define __SMP__ 1" >> $CONFIG_H
fi
printflag "Preemptive kernel support" CONFIG_PREEMPT
printflag "High memory support" CONFIG_HIGHMEM
if [ "$NEED_HZ" = "y" ] ; then
echo " Timer frequency (HZ) for the kernel is $CONFIG_HZ."
write_int CONFIG_HZ
fi
printflag "PCI BIOS support" CONFIG_PCI
printflag "Power management (APM) support" CONFIG_PM
printflag "SCSI support" CONFIG_SCSI
printflag "IEEE 1394 (FireWire) support" CONFIG_IEEE1394
printflag "Networking support" CONFIG_INET
printflag " Radio network interface support" CONFIG_NET_PCMCIA_RADIO
printflag " Token Ring device support" CONFIG_TR
printflag " Fast switching" CONFIG_NET_FASTROUTE
printflag " Frame Diverter" CONFIG_NET_DIVERT
printflag "Module version checking" CONFIG_MODVERSIONS
printflag "Kernel debugging support" CONFIG_DEBUG_KERNEL
if [ "$CONFIG_DEBUG_KERNEL" = "y" ] ; then
printflag " Memory leak detection support" CONFIG_MEMLEAK
printflag " Spinlock debugging" CONFIG_DEBUG_SPINLOCK
fi
printflag "Preemptive kernel patch" CONFIG_PREEMPT
if [ $VERSION_CODE -lt `version 2 1 7` ] ; then
printflag "PCMCIA IDE device support" CONFIG_BLK_DEV_IDE_PCMCIA
fi
printflag "/proc filesystem support" CONFIG_PROC_FS
case $ARCH in
i386) x86_config_tweak ; ;;
alpha) alpha_config_tweak ; ;;
ppc) ppc_config_tweak ; ;;
esac
if [ $VERSION_CODE -ge `version 2 4 0` ] ; then
write_bool CONFIG_RWSEM_GENERIC_SPINLOCK
write_bool CONFIG_RWSEM_XCHGADD_ALGORITHM
fi
}
echo "" >> $CONFIG
echo "" >> $CONFIG_MK
echo "" >> $CONFIG_H
if [ $ARCH = "i386" ] ; then
qgrep CONFIG_1GB $LINUX/include/asm-i386/page_offset.h && BIGMEM=y
qgrep CONFIG_HZ $LINUX/include/asm-i386/param.h && NEED_HZ=y
fi
CONFIG_PCMCIA=n
case $CONF_SRC in
1)
if [ -x /sbin/ksyms ] ; then
KSYMS="/sbin/ksyms -a"
else
echo "Hmmm... /sbin/ksyms is broken. Using /proc/ksyms..."
KSYMS="cat /proc/ksyms"
fi
echo "# Options from current kernel" >> $CONFIG
echo "# Options from current kernel" >> $CONFIG_MK
echo "/* Options from current kernel */" >> $CONFIG_H
echo "CHECK=\"/proc/version\"" >> $CONFIG
echo "CKSUM=\"`cksum < /proc/version`\"" >> $CONFIG
echo "#define CONFIG_MODULES 1" >> $CONFIG_H
if [ $VERSION_CODE -lt `version 2 3 37` ] ; then
if $KSYMS | grep CardServices | qgrep -v pcmcia ; then
CONFIG_PCMCIA=y
fi
else
symcheck PCMCIA dead_socket pcmcia_core
fi
if [ $VERSION_CODE -lt `version 2 2 0` ] ; then
symcheck SMP smp_invalidate_needed
else
symcheck SMP smp_num_cpus
fi
symcheck PREEMPT preempt_schedule
symcheck PCI pcibios
if [ $VERSION_CODE -lt `version 2 3 43` ] ; then
symcheck PM apm_register_callback
else
symcheck PM pm_register
fi
symcheck SCSI scsi_register scsi_mod
symcheck IEEE1394 hpsb_register_lowlevel ieee1394
symcheck SERIAL register_serial serial
symcheck PARPORT parport_register parport
symcheck PARPORT_PC parport_pc_ops parport_pc
symcheck PARPORT_PC_PCMCIA parport_pc_probe_port parport_pc
symcheck INET register_netdev
symcheck NET_FASTROUTE dev_fastroute_stat
symcheck NET_DIVERT divert_ioctl
if [ -r /proc/net/wireless ] ; then
CONFIG_NET_PCMCIA_RADIO=y
else
CONFIG_NET_PCMCIA_RADIO=n
fi
symcheck MODVERSIONS printk_R
if [ $VERSION_CODE -lt `version 2 1 7` ] ; then
symcheck BLK_DEV_IDE_PCMCIA ide_register
fi
symcheck TR tr_setup
symcheck HIGHMEM kmap_high
if [ "$BIGMEM" ] ; then
symcheck 1GB ^c01
symcheck 2GB ^801
symcheck 3GB ^401
fi
symcheck PROC_FS proc_root
symcheck PREEMPT preempt_schedule
symcheck KDB kdb_
symcheck DEBUG_MCOUNT mcount
symcheck MEMLEAK kmalloc_wrap
if [ $CONFIG_KDB = "y" -o $CONFIG_DEBUG_MCOUNT = "y" -o \
$CONFIG_MEMLEAK = "y" ] ; then
CONFIG_DEBUG_KERNEL=y
fi
if [ $ARCH = "i386" ] ; then
CONFIG_X86_PAE=n
if qgrep pae_pgd /proc/slabinfo ; then
CONFIG_X86_PAE=y
fi
symcheck EISA_bus EISA
elif [ $ARCH = "ppc" ] ; then
symcheck _prep_type ALL_PPC
fi
if [ $VERSION_CODE -ge `version 2 4 0` ] ; then
symcheck RWSEM_GENERIC_SPINLOCK __down_read
symcheck RWSEM_XCHGADD_ALGORITHM rwsem_wake
fi
echo "#ifndef __LINUX_MODVERSIONS_H" > $MODVER
echo "#define __LINUX_MODVERSIONS_H" >> $MODVER
H='[0-9a-f][0-9a-f]'
$KSYMS | sed -ne 's/.* \(.*\)_R\(.*'$H$H$H$H'\)/\1 \2/p' | \
awk '{ printf "#define %s\t%s_R%s\n", $1, $1, $2 }' \
>> $MODVER
echo "#endif" >> $MODVER
if [ "$NEED_HZ" = "y" ] ; then
echo "#include <linux/module.h>" > tmp.c
echo "#include <linux/sched.h>" >> tmp.c
echo "int init_module(void)" >> tmp.c
echo '{printk("<7>jif=%lu\n",jiffies);return-1;}' >> tmp.c
$KCC -DMODULE -D__KERNEL__ -Iinclude -I$LINUX/include -c tmp.c
/sbin/insmod tmp.o >/dev/null 2>&1
TICKS=`dmesg | sed -ne 's/^jif=//p' | tail -1`
CONFIG_HZ=`awk '{printf "%.0f",'$TICKS'/$1}' /proc/uptime`
fi
;;
2|3)
AUTOCONF=$LINUX/.config
if [ ! -r $AUTOCONF ] ; then
echo "Config file $AUTOCONF not present!"
echo " To fix, run 'make config' in $LINUX."
fail
fi
echo "# Options from $AUTOCONF" >> $CONFIG
echo "# Options from $AUTOCONF" >> $CONFIG_MK
echo "/* Options from $AUTOCONF */" >> $CONFIG_H
echo "CHECK=\"$AUTOCONF\"" >> $CONFIG
echo "CKSUM=\"`cksum < $AUTOCONF`\"" >> $CONFIG
echo "#define CONFIG_MODULES 1" >> $CONFIG_H
configcheck PCMCIA
if qgrep "^ *SMP *= *1" $LINUX/Makefile ; then
CONFIG_SMP=y
else
configcheck SMP
fi
if [ $VERSION_CODE -lt `version 2 1 7` ] ; then
configcheck BLK_DEV_IDE_PCMCIA
fi
if [ $VERSION_CODE -lt `version 2 3 43` ] ; then
configcheck APM ; CONFIG_PM=$CONFIG_APM
else
configcheck PM
fi
if [ $VERSION_CODE -ge `version 2 4 0` ] ; then
configcheck RWSEM_GENERIC_SPINLOCK
configcheck RWSEM_XCHGADD_ALGORITHM
fi
for C in PCI SCSI SERIAL INET NET_FASTROUTE NET_RADIO NET_DIVERT \
TR MODVERSIONS PROC_FS PARPORT PARPORT_PC PARPORT_PC_PCMCIA \
IEEE1394 NET_PCMCIA_RADIO KERNEL_DEBUGGING MEMLEAK PREEMPT \
DEBUG_KERNEL DEBUG_SPINLOCK PREEMPT HIGHMEM X86_PAE ; do
configcheck $C
done
if [ "$NEED_HZ" = "y" ] ; then
eval `grep "^CONFIG_HZ=" $AUTOCONF`
fi
if qgrep "^CONFIG_PARPORT_PC=y" $AUTOCONF ; then
CONFIG_PARPORT_PC=n
fi
if [ $CONFIG_KERNEL_DEBUGGING = "y" ] ; then
CONFIG_DEBUG_KERNEL=y
fi
if [ $CONFIG_NET_RADIO = "y" ] ; then
CONFIG_NET_PCMCIA_RADIO=y
fi
if [ $ARCH = "i386" ] ; then
configcheck EISA
elif [ $ARCH = "arm" ] ; then
configcheck ARCH_BRUTUS
configcheck ITSY
elif [ $ARCH = "ppc" ] ; then
for C in 8xx 4xx RPXLITE RPXCLASSIC MPC823 MPC850 MPC860 \
MPC860T ALL_PPC ; do
configcheck $C
done
fi
if [ "$BIGMEM" ] ; then
configcheck 1GB
configcheck 2GB
configcheck 3GB
fi
;;
esac
if [ "$FORCE" = "y" -a "$CONFIG_PCMCIA" = "y" ] ; then
CONFIG_PCMCIA=n
fi
if [ "$USE_PM" != "y" ] ; then CONFIG_PM=n ; fi
if [ ! -r $LINUX/include/linux/wireless.h ] ; then
CONFIG_NET_PCMCIA_RADIO=n
fi
if ! qgrep get_lynx_template $LINUX/drivers/ieee1394/pcilynx.c ; then
CONFIG_IEEE1394=n
fi
printconfig
echo ""
#=======================================================================
if [ "$CONFIG_PCI" != "y" -a "$CONFIG_CARDBUS" = "y" ] ; then
echo "Cardbus support requires kernel PCI bus support!"
echo " To fix, re-run 'make config' and disable Cardbus support."
fail
fi
if [ $VERSION_CODE -ge `version 2 5 0` -a "$CONFIG_PCMCIA" != "y" ] ; then
echo "2.5.0 and later kernels require that PCMCIA be configured in the"
echo " kernel source tree. To fix, reconfigure and rebuild your"
echo " kernel with PCMCIA enabled."
fail
fi
if [ ! -r $LINUX/include/asm ] ; then
cd $LINUX/include ; ln -s asm-$ARCH asm 2>/dev/null
fi
if [ ! -r $LINUX/include/asm ] ; then
echo "$LINUX/include/asm does not exist!"
echo " To fix, do 'ln -s asm-$ARCH asm' in $LINUX/include."
fail
fi
AFLAGS=
CONFIG_ISA=n
CONFIG_UID16=y
if [ $ARCH = "i386" ] ; then
CONFIG_ISA=y
elif [ $ARCH = "ppc" ] ; then
AFLAGS="-fno-builtin -msoft-float"
if [ $VERSION_CODE -ge `version 2 1 26` ] ; then
AFLAGS="$AFLAGS -ffixed-r2"
fi
elif [ $ARCH = "alpha" ] ; then
CONFIG_ISA=y
CONFIG_UID16=n
AFLAGS="-mno-fp-regs"
if [ $VERSION_CODE -ge `version 2 1 26` ] ; then
AFLAGS="$AFLAGS -ffixed-8"
fi
fi
write_str ARCH
write_str HOST_ARCH
write_str AFLAGS
write_bool CONFIG_ISA
if [ $VERSION_CODE -ge `version 2 3 40` ] ; then
write_bool CONFIG_UID16
fi
configcheckint NR_CPUS 32
write_int CONFIG_NR_CPUS
if [ $CONF_SRC != 1 -a "$CONFIG_MODVERSIONS" = "y" ] ; then
MODVER="$LINUX/$MODVER"
if [ ! -r $MODVER ] ; then
echo "$MODVER does not exist!"
echo " To fix, run 'make dep' in $LINUX."
fail
fi
else
# We may need at least an empty modversions.h file
touch $MODVER
fiecho "" >> $CONFIG
echo "" >> $CONFIG_MK
echo "" >> $CONFIG_H
#=======================================================================
if [ "$CONFIG_PCMCIA" = "y" ] ; then
# Use our kernel config, then kernel headers, then our headers
CPPFLAGS="-I../include/static -I\$(LINUX)/include -I../include"
else
# Use our kernel config and headers, then kernel headers
CPPFLAGS="-I../include -I\$(LINUX)/include"
fi
echo "CPPFLAGS=$CPPFLAGS" >> $CONFIG_MK
echo "" > tmp.c
WFLAG=-Wa,--no-warn ; $KCC $WFLAG -c tmp.c 2>/dev/null || WFLAG=
echo "WFLAG=$WFLAG" >> $CONFIG_MK
HAS_PROC_BUS=n
if [ $VERSION_CODE -ge `version 2 2 0` ] ; then
HAS_PROC_BUS=y
fi
write_bool HAS_PROC_BUS
if [ $VERSION_CODE -ge `version 2 1 7` -o \
"$CONFIG_BLK_DEV_IDE_PCMCIA" = "y" ] ; then
echo "DO_IDE=y" >> $CONFIG_MK
fi
if [ $VERSION_CODE -ge `version 2 3 6` ] ; then
CONFIG_PARPORT_PC=$CONFIG_PARPORT_PC_PCMCIA
fi
if [ $CONFIG_PARPORT_PC = "y" -a $VERSION_CODE -ge `version 2 2 0` ] ; then
echo "DO_PARPORT=y" >> $CONFIG_MK
fi
if [ $CONFIG_NET_PCMCIA_RADIO = "y" ] ; then
VER=`$KCC -E -dM ${LINUX}/include/linux/wireless.h | \
sed -ne 's/#define WIRELESS_EXT //p'`
if [ $VER -ge 10 ] ; then
echo "DO_ORINOCO=y" >> $CONFIG_MK
fi
fi
SCSI=$LINUX/drivers/scsi
if [ "$CONFIG_SCSI" = "y" -a "$CONFIG_CARDBUS" = "y" ] ; then
if qgrep ADAPTEC_1480A $SCSI/aic7xxx.c ; then
echo "DO_APA1480=y" >> $CONFIG_MK
NEW_AIC7XXX=n
elif [ -r $SCSI/aic7xxx/aic7xxx.c ] ; then
echo "DO_APA1480=y" >> $CONFIG_MK
NEW_AIC7XXX=y
elif [ "$CONFIG_PCMCIA" = "n" ] ; then
echo "The standalone Adaptec APA1480 CardBus driver is not" \
"supported with"
echo " this kernel. If you need it, use the kernel" \
"PCMCIA subsystem."
echo ""
fi
write_bool NEW_AIC7XXX
for f in aic7xxx.h aic7xxx/aic7xxx{,_linux,_osm}.h ; do
if [ -r $SCSI/$f ] ; then AIC7XXX_H=$f ; fi
done
echo "#define AIC7XXX_H <../drivers/scsi/$AIC7XXX_H>" >> $CONFIG_H
fi
if ! qgrep get_lynx_template $LINUX/drivers/ieee1394/pcilynx.c \
&& [ "$CONFIG_PCMCIA" = "n" ] ; then
echo "The standalone IEEE 1394 CardBus drivers are not" \
"supported with this"
echo " kernel. If you need them, use the kernel" \
"PCMCIA subsystem."
echo ""
fi
#=======================================================================
# Check out the module stuff
if [ "$CONFIG_PCMCIA" != "y" ] ; then
if [ ! -x /sbin/insmod -o ! -x /sbin/rmmod -o ! -x /sbin/lsmod ] ; then
echo "Your module utilities (insmod, rmmod) are missing from /sbin!"
echo " To fix, you should build and install the latest set" \
"of module tools,"
echo " available from FTP sites listed in the HOWTO."
fail
fi
MOD_RELEASE=`/sbin/insmod -V 2>&1 | \
sed -n -e 's/.*[Vv]ersion \([0-9][0-9.]*[0-9]\).*/\1/p'`
X=`echo $MOD_RELEASE | sed -e 's/\./ /g'`
MOD_CODE=`version $X`
if [ $VERSION_CODE -ge `version 2 1 85` ] ; then
NEED=`version 2 1 85` ; T=2.1.85
elif [ $VERSION_CODE -ge `version 2 1 18` ] ; then
NEED=`version 2 1 23` ; T=2.1.23
else
NEED=`version 2 0 0` ; T=2.0.0
fi
if [ $NEED -gt $MOD_CODE ] ; then
echo "Your module utilities are version $MOD_RELEASE. That is too old"
echo " for this kernel! To fix, upgrade to at least version $T."
fail
fi
fi
#=======================================================================
# Is the boot setup OK?
if [ "$PREFIX" = "" ] ; then
if [ -f /etc/lilo.conf -a -f /boot/map ] ; then
if [ /vmlinuz -nt /boot/map ] ; then
echo "Your boot map file is older than /vmlinuz. "\
"If you installed /vmlinuz"
echo "by hand, please run 'lilo' to update your boot"\
"data, and then reboot."
# else
# echo "Your 'lilo' installation appears to be OK."
fi
# else
# echo "It doesn't look like you are using 'lilo'."
fi
fi
#=======================================================================
# How should the startup scripts be configured?
if [ -z "$PREFIX" -a -z "$RC_DIR" ] ; then
if [ -d /sbin/init.d -o -d /etc/rc.d/init.d -o -d /etc/init.d ] ; then
echo "It looks like you have a System V init file setup."
SYSV_INIT=y
if [ -d /sbin/init.d ] ; then
RC_DIR=/sbin/init.d
elif [ -d /etc/rc.d/init.d ] ; then
RC_DIR=/etc/rc.d
else
RC_DIR=/etc
fi
else
echo "It looks like you have a BSD-ish init file setup."
if ! qgrep rc.pcmcia /etc/rc.d/rc.S ; then
echo " You'll need to edit /etc/rc.d/rc.S to invoke" \
"/etc/rc.d/rc.pcmcia"
echo " so that PCMCIA services will start at boot time."
fi
SYSV_INIT=
fi
write_bool SYSV_INIT
if [ "$SYSV_INIT" = "y" ] ; then write_str RC_DIR ; fi
elif [ -z "$PREFIX" ] ; then
write_bool SYSV_INIT
write_str RC_DIR
else
ask_bool "System V init script layout" SYSV_INIT
if [ "$SYSV_INIT" = "y" ] ; then
ask_str "Top-level directory for RC scripts" RC_DIR
fi
fi
#=======================================================================
# Optional stuff
HAS_XPM=n
if [ -r /usr/include/X11/Xlib.h -o \
-r /usr/X11R6/include/X11/Xlib.h ] ; then
echo "X Windows include files found."
for f in /usr/{X11/,X11R6/,local/,}lib/libXpm.{so*,a} ; do
if [ -r $f ] ; then break ; fi
done
for g in /usr/include/X11/xpm.h ; do
if [ -r $g ] ; then break ; fi
done
if [ -r $f -a -r $g ] ; then
echo "$f and $g found."
HAS_XPM=y
FLIBS="-L/usr/X11R6/lib -L/usr/X11/lib -lXpm -lX11"
else
echo "X PixMap library not installed."
fi
else
echo "The X11/Xaw libraries are not available."
fi
write_bool HAS_XAW
if [ "$HAS_XPM" != "y" ] ; then
echo " If you wish to build the 'cardinfo' control panel, you" \
"need the XPM"
echo " library and the X Windows include files. See the HOWTO" \
"for details."
echo " *You can ignore this message if you are only rebuilding the"
echo " PCMCIA modules.*"
HAS_XPM=n
fi
write_bool HAS_XPM
if [ "$HAS_XPM" = "y" ] ; then write_str FLIBS ; fi
HAS_WORDEXP=n
echo "#include <wordexp.h>" > tmp.c
$UCC $UFLAGS -c tmp.c 2>/dev/null && HAS_WORDEXP=y
write_bool HAS_WORDEXP
if [ "$HAS_WORDEXP" != "y" ] ; then
echo ""
echo "Your libc does not support wordexp()."
echo " Without wordexp(), cardmgr will not do command" \
"substitution or"
echo " environment variable expansion when parsing 'source'" \
"commands in"
echo " config files. To gain this feature, upgrade to a" \
"more recent"
echo " version of glibc."
fi
rm -f tmp.c tmp.o a.out
if [ ! -d /var/run ] ; then
echo "WARNING: /var/run not found."
echo " To fix, do 'mkdir /var/run'."
fi
#=======================================================================
# Where do man pages go?
md ()
{
L=`env LANG=en_US man -w $1 2>/dev/null | sed -ne 's+/man/.*+/man/+p'`
if [ -d "$L" ] ; then echo $L ; else echo $2 ; fi
}
MANDIR=`md ls /usr/man`
write_str MANDIR
XMANDIR=`md xterm /usr/X11R6/man`
write_str XMANDIR
#=======================================================================
mv -f $CONFIG config.out
touch .prereq.ok
echo ""
echo "Configuration successful."
echo ""
if [ "$CONFIG_PCMCIA" = "y" ] ; then
echo "** Your kernel is configured with PCMCIA driver support. Therefore,"
echo "** 'make all' will compile the PCMCIA utilities but not the drivers."
echo "** See README-2.4 if this is not what you intended!"
echo ""
echo "IMPORTANT NOTE FOR DEBIAN USERS:"
echo "This means that a pcmcia-modules package will not be built."
echo ""
fi